Bridging from Ethereum
The official PulseChain bridge supports transferring assets like USDC, DAI, ETH, HEX, and WBTC from Ethereum to PulseChain (and vice versa). It is the recommended native option for direct ETH → PulseChain transfers.
Key Details
| Supported tokens | USDC, DAI, ETH/WETH, HEX, WBTC, and others |
| Direction | Two-way (Ethereum ↔ PulseChain) |
| Time | Typically 10–30 minutes (depends on network congestion) |
| Fees | Small bridge fee (~0.3%) + Ethereum gas on source side. PulseChain side very low-cost. |
| Limits | Daily and per-transaction min/max apply (visible in bridge UI) |
| Security | Native/official bridge, strong track record. Always use links from pulsechain.com. |
Bridging HEX to stake it? Bridged HEX arrives on PulseChain as a separate wrapped token — it cannot be staked natively or made into an HSI, and so cannot back Actuator HTTs. To stake on PulseChain, bridge a stablecoin or ETH instead and swap it for native HEX once you arrive (the swap step below). Native PulseChain HEX shares its address with Ethereum HEX but is a distinct token with its own price — match by the token you receive from a swap, not by the name.
Bridged tokens arrive with no gas. A stablecoin, ETH, or HEX bridged to PulseChain lands in a wallet holding zero PLS — and every next step, including the swap above, needs a little PLS to pay for gas. A fresh wallet cannot pay for its own first transaction. Solution: bridge a small amount of wPLS. It arrives as spendable PLS for gas.
Note: The bridge site at bridge.pulsechain.com often points to IPFS-hosted or community-run versions of the interface for decentralization. Verify URLs carefully.
Prepare Your Wallet and Networks
- Use MetaMask (or compatible wallet like Rabby).
- Add the PulseChain network if not already present (Chain ID: 369, RPC URL and details on pulsechain.com).
- Ensure you have ETH on Ethereum for gas fees.
- Have USDC or DAI in your Ethereum wallet.
Go to the Bridge
- Visit bridge.pulsechain.com (bookmark it or use links from pulsechain.com).
- Connect your wallet and ensure it is set to the Ethereum network.
Select the Transfer
- Choose Ethereum as the source network.
- Select PulseChain as the destination.
- Pick the token: USDC or DAI.
- Enter the amount you want to bridge.
Approve and Confirm
- If this is your first time bridging that token, approve the spending allowance in your wallet.
- Review the details (amount, estimated fee, time).
- Confirm the transaction in your wallet (this locks/burns the tokens on Ethereum and initiates the bridge).
Wait for Completion
- Monitor the transaction status on the bridge interface (look for "Transactions" or status section).
- The process involves Ethereum confirmation + relay to PulseChain.
Receive on PulseChain
- Switch your wallet network to PulseChain.
- The bridged USDC or DAI should appear in your wallet balance.
- Verify the token contract address via scan.pulsechain.com if needed.
Post-Bridge Actions (Optional)
- Go to PulseX DEX (app.pulsex.com) or another PulseChain DEX.
- Swap bridged USDC/DAI for native PLS, PLSX, HEX, or other tokens.
- Check liquidity/pools on Dexscreener or similar before large swaps.
Important Tips and Warnings
- Start small: Test with a small amount first to confirm everything works.
- Liquidity check: Ensure there is sufficient liquidity for the bridged token on PulseChain DEXes. Tools like Dexscreener can help.
- Gas and timing: Bridge during lower gas periods on Ethereum for cheaper/faster transactions.
- Reversing the bridge: Select PulseChain as source and Ethereum as destination; switch networks accordingly.
- Risks: Standard bridge risks (though this one is native and proven). Never share seed phrases. Double-check all addresses and URLs.
- Alternatives: Liberty Swap, Rubic, or others — but the official bridge is preferred for direct ETH ↔ PulseChain stablecoin transfers.
Actuator ACTR Contract:
0x85DF7cE20A4CE0cF859804b45cB540FFE42074Da